Originally Posted by
p45cal
What is 'one set'? Is it as if there were only one row of data in the table at the top of the sheet PT REL?
Eg. this is what's produced in the clipboard if only one line is processed - is it correct?:
*TDN-PROFILE ; Tendon Profile
NAME=L-S9_GD_1LB_L, 0.6in PS Strand, 13113to13124, 0, 0, ROUND, 2D
Frame 2, Auto2,,,YES,8
ELEMENT, END-I, 13113, I-J
0, YES, 0, 0
Y=0, -0.973958333333333, NO, 0, 0, NONE,,,,NO
Y=45, -0.973958333333333, NO, 0, 0, NONE,,,,NO
Z=0, -3.79166666666667, NO, 0, 0, NONE,,,,NO
Z=45, -3.79166666666667, NO, 0, 0, NONE,,,,NO
NAME=L-S9_GD_1LB_R, 0.6in PS Strand, 13113to13124, 0, 0, ROUND, 2D
Frame 2, Auto2,,,YES,8
ELEMENT, END-I, 13113, I-J
0, YES, 0, 0
Y=0, 0.973958333333333, NO, 0, 0, NONE,,,,NO
Y=45, 0.973958333333333, NO, 0, 0, NONE,,,,NO
Z=0, -3.79166666666667, NO, 0, 0, NONE,,,,NO
Z=45, -3.79166666666667, NO, 0, 0, NONE,,,,NO
NAME=R-S9_GD_1LB_L, 0.6in PS Strand, 13113to13124, 0, 0, ROUND, 2D
Frame 2, Auto2,,,YES,8
ELEMENT, END-I, 13113, I-J
0, YES, 0, 0
Y=0, 0.973958333333333, NO, 0, 0, NONE,,,,NO
Y=45, 0.973958333333333, NO, 0, 0, NONE,,,,NO
Z=0, -3.79166666666667, NO, 0, 0, NONE,,,,NO
Z=45, -3.79166666666667, NO, 0, 0, NONE,,,,NO
NAME=R-S9_GD_1LB_R, 0.6in PS Strand, 13113to13124, 0, 0, ROUND, 2D
Frame 2, Auto2,,,YES,8
ELEMENT, END-I, 13113, I-J
0, YES, 0, 0
Y=0, -0.973958333333333, NO, 0, 0, NONE,,,,NO
Y=45, -0.973958333333333, NO, 0, 0, NONE,,,,NO
Z=0, -3.79166666666667, NO, 0, 0, NONE,,,,NO
Z=45, -3.79166666666667, NO, 0, 0, NONE,,,,NO
*USE-STLD, Prestress
*TDN-PRESTRESS
L-S9_GD_1LB_L, FORCE, BOTH, 43.9375, 43.9375, 0, Prestress
L-S9_GD_1LB_R, FORCE, BOTH, 43.9375, 43.9375, 0, Prestress
R-S9_GD_1LB_L, FORCE, BOTH, 43.9375, 43.9375, 0, Prestress
R-S9_GD_1LB_R, FORCE, BOTH, 43.9375, 43.9375, 0, Prestress
If this is not the case, then edit the above output to show what you do want for just that base name S9_GD_1LB